100% satisfaction guarantee /Painters across metropolitan Adelaide

Exterior Painting

How Rendered Walls Are Painted, and Why Cracks Come Back

Rendered walls are washed, repaired with flexible fillers, sealed and given two coats of masonry acrylic. Cracks return when the wall keeps moving or the filler is too rigid.

Weathered rendered wall with a web of fine cracks running through its white paint above a band of textured orange render

Rendered walls are washed, repaired with flexible fillers, sealed and then given two coats of an exterior acrylic made for masonry. Cracks come back when the wall keeps moving, which is common on Adelaide's reactive clay soils, or when they were filled with a rigid product that cannot stretch. Paint can hide and bridge fine cracks, but it cannot hold a moving wall together.

Why render needs its own paint system

Most Adelaide render is either cement render over brick or block, or an acrylic render system, sometimes over foam or fibre cement cladding. Cement render is alkaline when new, porous and slightly textured. It needs a paint that tolerates alkali, lets water vapour pass through, and flexes enough to cope with small movement. Exterior acrylic masonry paints are made for this. Gloss enamels and interior wall paints are not.

New render needs time to cure before it is painted, often several weeks, and the render manufacturer will state the minimum. Painting too early can trap moisture and lime, which later shows as blotchy colour or lifting paint.

The usual steps on a repaint

  1. Wash. Dirt, cobwebs, mould and chalk come off first. A pressure washer helps on sound render when used with care, but it can force water into cracks and damage soft or failing render. Our post on pressure washing before painting covers when it helps.
  2. Scrape and assess. Loose paint is removed, and drummy render, which sounds hollow when tapped, is marked for repair.
  3. Repair cracks. Fine cracks are opened slightly so filler can key in; larger ones may be raked out and patched with render.
  4. Treat salts and mould. Salt deposits are brushed off dry and the source of water looked at. Mould is killed, not painted over.
  5. Seal. A masonry sealer or binding primer goes on new patches, bare render and chalky areas, so the topcoat has a firm base and even absorption.
  6. Two topcoats. Applied by roller, brush or spray at the spread rate on the tin, so the film is thick enough to last.

Why cracks come back

A crack that reappears after painting is usually telling you one of three things.

The filler was too rigid

A hard patching compound sets solid in the crack. When the wall moves even slightly, the patch stays put and the crack opens again beside it. Exterior render cracks need a flexible acrylic filler or sealant that can stretch, and the paint over it needs some give too.

The wall moves with the seasons

Much of Adelaide sits on reactive clay that swells when wet and shrinks when dry. Footings rise and fall a little through the year, and render cracks in predictable places: from the corners of windows and doors, where old work meets new, and along lines where a control joint was never put in. Cracks that open in late summer and close in winter are a classic sign. The background is explained in why Adelaide walls crack.

The crack is structural

Cracks that are wide, stepped through the brickwork, getting longer, or making doors stick are not a painting problem. Have them assessed by a builder or structural engineer before spending money on paint.

Membrane coatings for walls that keep cracking

Where a wall has many fine, active cracks, a high build elastomeric or membrane coating can be a better choice than standard masonry paint. These go on much thicker and stretch over hairline movement, so cracks are less likely to telegraph through. They will not cope with large movement, and they only work at the correct film thickness over sound preparation. Their finish is also slightly rubbery and textured, which suits some walls more than others.

Acrylic render and cladding systems

Textured acrylic render over foam or fibre cement is common on newer homes. It is often part of a specified system, and very dark colours may be restricted because heat can cause movement in the backing boards. Before repainting, it is worth finding out what was originally used and checking the system manufacturer's advice on recoating products and colour limits.

Render is one of the most common surfaces our exterior painters deal with, and the behaviour of the cracks usually decides which system goes on the wall.

Keep reading

Related guides

All articles

Free quotes

Want it done properly, first time?

Prefer to leave it to the professionals? We quote every job free, after a site visit.

Call us Free quote