100% satisfaction guarantee /Painters across metropolitan Adelaide

Preparation & Repairs

Should You Sand Between Coats of Paint?

On doors, trims and anything in enamel, yes: a light sand between coats gives a smoother finish and better adhesion. On flat or low sheen walls it is usually only needed to knock off bits.

Tradesman using a sanding block to smooth white-painted cabinet doors laid across sawhorses in a workshop

It depends on what you are painting. On doors, skirtings, architraves, window frames and cabinetry, especially in enamel, a light sand between coats is worth the effort: it removes dust nibs and brush marks and gives the next coat a slightly keyed surface to grip. On walls in flat or low sheen acrylic, a full sand between coats is rarely needed. A quick check for bits, drips and roller fluff is usually enough.

What sanding between coats actually does

It is not about taking paint off. A light pass with fine abrasive does three things:

  • Removes defects. Dust specks, insects, brush hairs and small runs get flattened before they are locked in by the next coat.
  • Levels the surface. Brush marks and slight orange peel are knocked down, which matters most on gloss finishes that show every ripple.
  • Improves adhesion. Fine scratches give the next coat more surface to hold on to, particularly on harder enamels.

Done well, you end up with a finish that feels smooth under your hand rather than gritty. That matters most on surfaces people touch every day, such as door edges, handrails and window sills, where a rough or bumpy finish is noticed straight away.

Which grit to use

As a general guide:

  • Preparing bare timber or old paint: coarser grits around 120 to 180 to remove gloss and level repairs.
  • Between undercoat and topcoat: around 220 to 240.
  • Between finish coats of enamel: around 240 to 320, sometimes finer on high gloss work.

Sanding sponges and flexible pads follow mouldings on doors and architraves better than a hard block. On flat panels, a block keeps the surface even. Use light pressure. If you cut through to the colour underneath, you have gone too far, and that spot needs touching up before the next coat.

Enamel versus acrylic

Enamels, whether water based or solvent based, dry harder and show surface flaws more, so they gain the most from sanding between coats. Solvent based enamel also needs sanding for the following coat to bond well once it has cured past the recoat window. Water based enamels are a little softer early on, so give them their full recoat time before sanding. Our guide on why trims and doors get enamel covers these finishes in more detail.

Wall acrylics in flat and low sheen are forgiving. Sanding them aggressively can burnish the surface, leaving shiny patches. Instead, run your hand over the wall after the first coat, knock off any bits with fine paper, and move on.

Is the paint ready to sand?

This is where people go wrong. Paint can be touch dry long before it is ready to sand. If it clogs the paper, rolls into little gummy balls or leaves smeared marks, it is too soft. Stop and wait. Properly dry paint sands to a fine white powder. Recoat and sanding times vary with temperature, humidity and the product, so check the tin. Our article on how long paint takes to dry and cure explains the difference between touch dry, recoat and cure.

Dust removal is part of the job

Every bit of sanding dust left behind becomes a lump in the next coat. After sanding:

  1. Brush or vacuum dust from mouldings, panel edges and the tops of skirtings.
  2. Wipe surfaces with a slightly damp lint free cloth, or a tack cloth on solvent based work.
  3. Let any moisture evaporate before painting.
  4. Vacuum the floor nearby so you do not kick dust back up while painting.

When to skip it

You can skip a full sand when the first coat went on clean, the surface is flat or low sheen, and you are applying the next coat within the recoat window. You still want to fix any visible defect before it is buried.

On older homes, sanding the existing paint is a different matter. Paint applied before 1970 may contain lead, and it should be tested before any sanding. That applies to preparation, not to sanding fresh modern coats.

Between coat sanding on doors and trims is part of how we work on interior painting jobs, because those are the surfaces people touch and look at most closely.

Keep reading

Related guides

All articles

Why Is My Exterior Paint Peeling?

Exterior paint peels when it loses its grip. The usual causes are moisture behind the paint, poor preparation, incompatible…

4 min read

How to Fill Cracks Before You Paint

Open the crack slightly, clean out the dust, fill with a product that suits the crack type, then sand flush and seal before…

4 min read

Free quotes

Want it done properly, first time?

Prefer to leave it to the professionals? We quote every job free, after a site visit.

Call us Free quote