100% satisfaction guarantee /Painters across metropolitan Adelaide

Interior Painting

Should You Paint the Ceiling or the Walls First?

Ceiling first, then walls, then trims and doors. Working from the top down means drips land on surfaces you have not painted yet, and each stage tidies the edge of the one before.

Man in a hard hat and safety glasses standing on a stepladder brushing white paint onto a ceiling beside louvre windows

Paint the ceiling first. Then the walls, then the skirting boards, architraves, window frames and doors. Working from the top down means any drips, spatter or roller mist fall onto surfaces that are still to be painted, and each new stage neatens the edge left by the one above. It is the order most professional painters follow, and there are good reasons behind it.

Why the ceiling goes first

Rolling a ceiling throws a fine mist of paint downwards. Even with careful technique, some of it lands on the top of the walls and occasionally further down. If the walls are already finished, those specks have to be touched up, and touch ups on a wall often show. If the walls have not been painted yet, the spatter simply gets covered.

There is also the matter of the ceiling line itself. Where the ceiling meets the wall, or meets the cornice, the paint from the ceiling will inevitably creep slightly onto the wall. When the walls are painted next, the wall colour is cut in neatly up to that line, which gives a sharp finish. Doing it the other way round would mean cutting a white ceiling against a coloured wall overhead, which is much harder to keep straight.

For tips on getting the overhead part right, have a look at painting a ceiling without streaks.

The full order, step by step

  1. Prepare the whole room. Fill, sand, gap fill and spot prime every surface before any finish coats go on. Dust from sanding settles on wet paint, so it pays to get it all done first.
  2. Ceiling. Cut in around the edges and fittings, roll, and apply the second coat once the first is ready.
  3. Cornices. Usually painted with the ceiling in the ceiling colour, though some homes pick them out separately.
  4. Walls. Cut in to the cornice, around windows, doors and skirtings, then roll. Two coats.
  5. Trims. Skirting boards, architraves, window frames and picture rails, usually in enamel.
  6. Doors. Last, so they can dry without being brushed past, and often with the hardware removed.

Walls before trims, or trims before walls?

This is where painters genuinely differ. Many prefer walls first, then trims, because a brush loaded with enamel can be pulled along the top of a skirting board to leave a crisp edge against a dry wall. Others do the trims first, let them cure a little, then mask them and paint the walls, because masking a hard enamel is easy and the tape line comes out very clean.

Both work. What matters is that the second stage is cut in with care, and that whatever goes first is properly dry before anything is taped or brushed against it. The quality of the line depends far more on brush skill than on the order. That skill has a name, and we explain it in what cutting in is and why it matters.

What about a feature wall or two colours?

If one wall is a different colour from the rest, paint the lighter colour first, including a little onto the edge of the feature wall. Once it is dry, cut in the darker colour along the internal corner. Dark over light covers in fewer coats than light over dark, and the corner gives a natural place to stop.

The same logic applies when walls and ceiling share the same colour, a look sometimes called colour drenching. The order stays the same, but the cut lines between ceiling and wall become less critical because there is no contrast to show a wobble.

Timing it across a whole house

When a painter works through several rooms, the order applies within each room, but the rooms themselves get staggered. While one ceiling dries, the walls of the next room might be getting their first coat. It keeps the job moving without anyone recoating paint that is not ready. Recoat times vary between products, so the tin is the guide for how long to leave each layer.

If you are doing it yourself, resist the urge to finish one wall completely before starting another. Do each stage across the whole room. It is quicker, and you will get a more consistent result.

One more tip: protect the floor until the very end

The order is about protecting finished work, and the floor is the last finished surface in the room. Keep drop sheets down until the doors and skirtings are done, because skirting boards are close to the floor and enamel drips are hard to remove from timber or carpet once dry.

If you would rather hand the whole sequence to someone else, our interior painters handle ceilings, walls and woodwork as one job, in the right order.

Keep reading

Related guides

All articles

Free quotes

Want it done properly, first time?

Prefer to leave it to the professionals? We quote every job free, after a site visit.

Call us Free quote